Link To Digitrax for more information on these fine products
UT6D Duplex Equipped Utility Throttle
Part # UT6D
$180.00
Click to order
FHS Custom Length Data Cables
These cables can be ordered from 5 to 40 feet in length.
These feature Standard RJ-12 connectors with wire colors matched on each end for use with Digitrax or NCE systems.
Cable is white in color.
Part # Data Cable
$5.49 to 18.39
Click to order
BD4 Quad Occupancy Detector
Cost Effective occupancy detection for 4 detection sections
Outputs for panel mounted LEDs to display occupancy
Detects any powered locomotive
Detects un-powered rolling stock equipped with resistor wheel sets
Transmits occupancy information to your LocoNet System using DS54 or SE8C (sold separately).
BD4 Instructions
Part # BD4
$37.00
Click to order
BD4N Quad Occupancy Detector
Low-cost, High-sensitivity DCC block-occupancy detection.
Adjustable resistance/current detection section (DS) trip threshold.
8A capacity, suitable for all scales and track wiring configurations.
Noise resistant and compatible with BDL168 sections.
On-board status leds for stand-alone occupancy and track power indication, expandable for optional LT5 or fascia mounted occupancy indicator leds.
Plug and Play connections to simplify setup. Can cascade Booster wires.
Isolated Occupancy output signal lines can drive most common signal system or control interfaces.
Compatible with DS64 and SE8 modules for signaling, control and reporting occupancy onto LocoNet.
Replaces the BD4.
Part # BD4N
$37.00
Click to order
RX4 4-Zone Transponding Receiver Add-on for BDL Series Detectors
4 ZoneTransponding Receiver Add-on for BDL16 series occupancy detectors.
Use up to two RX4s with a BDL168 to add transponding to any 8 detection sections on your layout.
Use one RX4 with a BDL162 or BDL16 to add transponding to any 4 detection sections on your layout.
(Note: BDL16 & BDL162 are discontinued).
Part # RX4
$54.00
Click to order
RD2 Remote Diode for BDL168
Remote sensing of 2 detection sections. Eliminates the need for long runs of heavy gauge wire between the BDL16 & remotely located track sections.
RD2 Instructions
Part # RD2
$12.00
Click to order
MS100 Computer Interface
The MS100 Computer Interface is designed to let a computer with an IBM compatible COM, or RS232 communications port, monitor Digitrax LocoNet. Application software running in the computer can then interpret the activity on the LocoNet and report back to the user via the computer screen. The MS100 is a signal level translator between LocoNet and a 25 pin DB25 style RS232 port.
Part # MS100
$45.00
Click to order
PS14 Power Supply
The PS14 is a 300ma, 14 Volt power supply for powering Digitrax accessories like the UP5, BDL168, DS64, SE8C, LNRP, UR90 & UR91 and others
Part # PS14
$16.00
Click to order
PS615 Power Supply 6 Amp
PS615 90W AC/DC 15VDC 6 amp power supply for use with all Digitrax Command Stations and Boosters operating at 5 amps.
High-efficiency power supply
15 VDC output
Accepts different cord sets
Meets MEPS VI and DOE VI efficiency standards
CE for EM compatibility and IEC 60950, UL, and FCC safety requirements
Full galvanic isolation of output voltage from AC input
RoHS environmentally sensitive manufacturing
Compact and lightweight
Power indicator light
Over current and overload protected
Part # PS615
$79.00
Click to order
PM74 Power Manager
PM74 Power Manager with Occupancy and Transponding detection for 4 sub-districts
4 Power Manager sub-districts.
Upgraded replacement for PM42, fully encased.
Fully connectorized installation.
Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit management.
Each DS supports Occupancy detection.
Each DS supports Transponding detection.
Allows Mainline CV Read/Write program of compatible decoders.
Remote LED status support.
Series7 style advanced installation support using DT602.
Replaces PM42 Quad Power Manager.
Part # PM74
$109.00
Click to order
