FHS Custom Length Data Cables
These cables can be ordered from 5 to 40 feet in length.
These feature Standard RJ-12 connectors with wire colors matched on each end for use with Digitrax or NCE systems.
Cable is white in color.
Part # Data Cable
$5.49 to 18.39
Click to order
NCE USB Interface
Add this USB computer interface for computer programming and/or operation of your Power Cab equipped layout. Requires USB cable, computer and railroad computer program such as JMRI Decoder Pro and Panel Pro. Can be used with the PH Pro and PH10 systems. HOWEVER, with the PH systems you can only RUN or OPERATE railroads with it. You can not use the USB Interface to Program decoders.
Part # NCE-USB
$64.95
Click to order
NCE Switch 8 Mk-2
Control for 8 Tortoise switch machines – Remembers the position of switch during power outages – Supports the full range of DCC accessory addresses (1-2044) – Easy address programming, no need to connect it to programming track – Connect optional “Button Board” for local push button control – Simple hook up, 2 wires to the track, 2 wires to each switch machine
Part # NCE-151
$89.95
Click to order
NCE Button Board for Switch 8 Mk-2
Add up to 16 push buttons to Switch8-Mk2 – Accommodate N.O. Pushbuttons or toggle switches – Simple hook up, 3 wires to Switch8-Mk2
Part # NCE-152
$39.95
Click to order
NCE Switch-It Mk-2
FOR STALL MOTOR MACHINES ONLY, NOT FOR USE WITH TWIN COIL SWITCH MACHINES
All new easy programming!
Control for 2 Tortoise switch machines
Remembers the position of switch during power outages
Supports the full range of DCC accessory addresses (1-2044)
Easy address programming, no need to connect it to programming track
Push button connections for local control panel operation
Simple hook up, 2 wires to the track, 2 wires to each switch machine
Part # NCE-154
$39.95
Click to order
NCE Snap-It
Snap-It is an accessory decoder for one Atlas type twin coilswitch machine. Can also have capacitor added for extra power.
Part # NCE-0115
$25.95
Click to order
NCE P519
Dimensions: 6.5 x 2.5 x 1.5
The P519 is a 19 Volt DC, 4.74 amps, 90 Watt with US power cord.
Power supply suitable for use with the following NCE products: PH5 (5 Amp system) and PB5a Booster.
Note: For PowerPro (5 Amp system) PB105 booster. For use with these older NCE systems Customer should cut off the round connector,
then strip the cable to expose the two wires that connect to your system’s screw terminals.
Input is not polarity sensitive.
NOT FOR USE WITH SB5, DB5 or PB5 BOOSTERS
This product has the required international approvals for use in the following countries: USA,
Canada, UK, Scotland, Ireland, Australia, New Zealand, Argentina, Mexico, Norway, and Japan.
Part # NCE-P519 (NCE # 325)
$99.95
Click to order
NCE P114 524221 Power Supply
NCE 524221 | 5240221 Power Cab Power Supply, P114 24 Watt 13.8v DC Power Supply for U.S. Power Cab
Part Number: 5240221
Input 120VAC/220VAC, output 13.8 VDC 24 watt.
5.5 mm barrel plug with a 2.5mm center plug (center is +)
Additional or replacement DC power supply for the Power Cab system and other model railroad uses.
When used with the UTP – Universal Throttle Panel this will add power to the cab bus for larger layouts.
The Power Cab has a built in over current sensing for basic self-protection that will continuously try to reset until destroyed if left uncorrected.
Neither the Power Cab or the P114 have manual circuit breakers that will trip or fuses that will blow.
Use a DCC circuit breaker like the EB1v1.1 to protect your system.
Don’t forget to use a REAL surge protector not a power strip
Part # NCE-P114
$29.95
Click to order
